SLL's embedded software innovation has been recognised by our customers and partners. Major FPGA, memory, and development board makers now officially partner with SLL. This ensures SLL IP is validated on a wide range of physical devices. SLL customers are located in most geographical regions, and include Fortune Global 500's, government agencies, and SME's from USA and Canada to China.
SLL product portfolio page for
FPGA and SOC modules, carrier boards, development boards and CRUVI boards
SLL is Trenz Electronic’s partner
SLL is an Infineon Associated Partner
SLL is JSC’s partner
Micron Technology, Inc
SLL collaborates closely with Micron
SLL is GigaDevice’s partner
SLL is Winbond’s partner
SLL collaborates closely with Macronix
Overview of SLL's support for Trenz boards that use Intel FPGA and SoC FPGA devices
SLL supports the following products and services on Trenz boards that use Intel FPGA and SoC FPGA device families:
Overview of SLL's support for Trenz boards that use AMD-Xilinx FPGA and SoC FPGA devices
SLL supports the following products and services on Trenz boards that use AMD-Xilinx FPGA and SoC FPGA device families:
Trials of SLL IP for FPGA and SoC FPGA
To request a Trial of SLL’s IP for FPGA and SoC FPGA, please visit here.
Trenz Electronic CR00100-01
The Trenz Electronic CR00100-01 is a CRUVI base board with Intel™ FPGA.
- Intel™ 8k LE MAX10 FPGA (10M08)
- JTAG and UART over Micro USB connector
- 2 x User Push button
- 4 x User LEDs (red, green)
- 1 x CRUVI LS
- 1 x CRUVI HS
- Compatible with Trenz HS CRUVI memory boards (CR00041)
- Supports HyperBus, OctaBus, Xccela Bus, …
- x8/x16 PSRAM
- x8 NOR Flash
- Compatible with Trenz HS CRUVI memory boards (CR00041)
SLL’s provides reference designs with a Trial of SLL’s xSPI MBMC memory controller to customers for use with this low cost evaluation board.
SLL xSPI MBMC support for Trenz Electronic Base Boards
Status of board testing and qualification performed by SLL with SLL’s xSPI MBMC memory controller:
- Trenz Electronic GmbH
- Cyclone 10 LP RefKit 10CL055 Development Board (TEI0009-02-055-8CA) – Validated
- S7 Mini – Fully Open-Source Module with Xilinx Spartan-7 7S25 + 64 MBit HyperRAM (TE0890-01-25-1C) – Validated
- Artix-7 100T FPGA Module with Xilinx XC7A100T-2CSG324I (TE0725-03-100-2I9) – Validated
- ZedBoard Zynq-7000 ARM/FPGA SoC Development Board with a proprietary FMC HyperBus board – Validated
- FPGA Module with Xilinx Artix-7 100T (TE0725LP-01-100-2L) – Pending
- Trenz Electronic CRUVI – MAX 10 (CR00101) – Validated
- Trenz Electronic CRUV – Cyclone 10 LP – Ref Kit ( CR00109-01 ) with a wide range of xSPI devices – Pending
- Trenz Electronic 4 x 5 Module Carrier for CRUVI Extension Boards (TEB0707) has been validated with a wide range of xSPI devices using the following SoM
- FPGA Module with Xilinx Artix-7 XC7A200T-2FBG484C, 1 GByte DDR3L – Validated
- MPSoC Module with Xilinx Zynq UltraScale+ ZU3CG-1E, 2 GByte DDR4 SDRAM (TE0820-04-3AE21FA) – Validated
- MPSoC Module with Xilinx Zynq UltraScale+ ZU2CG-1E, 4 GByte DDR4 SDRAM (AM0010-01-2AE21MA) – Pending
SLL memory device support on FPGA and SoC FPGA
SLL’s memory controller portfolio supports a very broad range of memory devices from many memory vendors.
xSPI MBMC IP currently supports, or will very soon support:
- AP Memory® Xccela™ PSRAM, OctaRAM™ and QSPI DDR PSRAM
- Everspin® SPI Industrial STT-MRAM Persistent Memory (EM064LX)
- Gigadevice® NOR Flash (GD25X, GD25LX)
- Infineon® HyperRAM™ 2.0 with HyperBus™ Interface and HyperRAM™ 2.0 with Octal Interface
- Infineon® Semper™ Flash with HyperBus™ Interface and Semper™ Flash with Octal Interface
- Infineon® (Cypress®) HyperFlash™ 1.0
- Integrated Silicon Solution Inc.® (ISSI) HyperRAM™ 1.0 (Revision D dies or higher only), HyperRAM 1.0™ with inbuilt ECC and HyperFlash™ 1.0
- ISSI® x8 Octal RAM and Octal RAM with inbuilt ECC
- ISSI® x8 Octal Flash (NOR Flash)
- ISSI® x8 Octal MCP
- Jeju Semiconductor Corp® (JSC) OctaRAM™
- Macronix® OctaBus™ / OctaFlash™ (NOR Flash)
- Micron® Xccela™ Flash (NOR Flash)
- Winbond® HyperRAM™ 1.0 and HyperRAM™ 2.0
- Winbond® OctalNAND for use with Linux (W35N01JW, W35N02JW, W35N04JW)
Contact SLL for more information: info@synaptic-labs.com
